Paper & Packaging Testing Instruments

• Microprocessor based display for accurate test results
• Highly accurate test results under uniform compression Force
• TARE and Peak Hold Facility Available
• Over travel protection
• Strong base plate with rugged structure
• Bright LED display
• Feather touch controls

• Display- LED (Digital)
• Accuracy- ± 2% full scale (with master load).
• Power- 220V, Single / Three phase, 50 Hz
• Test Speed- 12.5 ± 2.5 mm/min

• Microprocessor based with original Intel chip
• TARE facility
• Peak Hold facility for keeping the maximum value in memory
• Bright LED display
• Calibration facility available
• Feather touch controls

Specification:

• Capacity- 40 kg/cm²
• Display- LED (Digital)
• Accuracy- ± 1% within 10% t o 90% of entire range as per IS: 1828 with master gauge
• Least Count/Resolution- 0.1Kg/cm²
• Power- 220V, Single phase, 50 Hz
• Test fluid- Glycerinabout 98% purified(lab grade)
• Rate of fluid displacement- 95 cc/minute
• Motor- 1/4 HP Single Phase , 1440 rpm
• Test Range- 1Kg/cm² to 38 Kg/cm²

• It measures the bursting capacity of Woven, non-woven and knitted fabrics, paper, paper board and corrugated boxes

• BS 3424/3137
• ASTM 3786
• ISO 2758/2559/3303/3689
• Reference Standard: IS 1060, Part-I 1987

Features:

• Ease of installation, high accuracy, and fine performance.
• Calibration facility is also available.
• Single Push Button Operation
• Highly accurate test results under multidirectional Force
• Strong Gripping clamps
• Grooved structure of Test Specimen Holder to avoid slippage and intact holding of specimen under test
• No slippage in case specimen is tightened uniformly using operating wheel

Specification:

• Capacity- 0 – 7 kg/cm² and 0 – 35 kg/cm²
• Display- Analogue
• Accuracy- ± 1% within 10% to 90% of entire range as per IS:1828 with master gauge.
• Least Count/Resolution- 0.2 Kg/cm2 for Gauge I, 1.0 kg/cm2 for Gauge II
• Power- 220V, Single phase, 50 Hz
• Test fluid- Glycerin about 98% purified (lab grade)
• Rate of fluid displacement- 95 cc/minute
• Motor- 1/4 HP Single Phase , 1440 rpm
• Gauge Selection- Through Needle Valve

• Single Push Button Operation
• Auto Sample Locking under selectable pressure range
• Microprocessor based display for accurate test results
• Peak Hold facility for keeping maximum value of test result in memory
• Memory to hold up to 9 test reading
• Highly accurate test results under multidirectional Pneumatic Force
• Strong Gripping clamps
• Grooved structure of Test Specimen Holder to avoid slippage and intact holding of specimen under test
• Bright LED display
• Feather touch controls
• Calibration lock & key feature

• Capacity- 40 kg/cm²
• Display- LED (Digital)
• Specimen Clamping- Pneumatic
• Accuracy- ± 1% within 10% t o 90% of entire range as per IS : 1828 with master gauge
• Least Count/Resolution- 0.1Kg/cm2
• Pressure Sensor- Pressure Transducer
• Power- 220V, Single phase, 50 Hz
• Test fluid- Glycerin about 98% purified (lab grade)
• Rate of fluid displacement- 95 cc/minute
• Motor- 1/4 HP, Single Phase, 1440 rpm

• High Quality rugged structure with corrosion resistant main body
• Light weight and resilient
• Fast Locking Mechanism
• Single handed hassle free operation
• Highly accurate test results
• High Grade stainless steel test area

• Sample Diameter- 130 mm (approx)
• Depth of cylinder- 60 mm
• Diameter of rubber pad- 145 mm
• Water level indicator in cylinder- 10 mm and 25 mm
• Weight of roller- 10Kg (approx)

• Motorised Weight arrangement on sample for noise free working
• Highly accurate test results under uniform load and specified movement.
• Uniform load by weights on test sample for evenness in testing
• Provision of Set number of counts through Digital Preset Counter
• Firm hold of test specimen by circular clips/clamps
• Motorised Geared system for scuff movement
• Digital Pre-settable counter upto 9999 counts
• Highly accurate and precise results under uniform load and rubbing clamp movement
• Accurate rpm of upper rotating discs using synchronous motor
• User friendly electronic controls and ergonomically designed feature
• Adjustable footrest for leveling

• Test Weight- 2 psi
• Counter- 4- digit Digital Preset type
• Max.range of counter- 9999
• Least Count of counter- 1
• Rotational Speed- 60 rpm ± 2 rpm
• Lower Motor capacity- ¼ HP
• Upper Motor capacity- 10 kg/cm² torque motor
• Diameter of Upper Clamp- 48 ± 2 mm
• Diameter of Lower Clamp- 120 ± 2 mm
• Power- 220V, 50Hz, single phase

The Presto grammage checking kit comprises of the GSM round cutter along with Digital weighing balance. GSM round cutter with imported industrial blades gives you a very accurate & seamless cutting of your samples.

Features:

GSM Cutter:-

• High Quality Aluminum pressure die casted main body
• Light weight and resilient
• Highly accurate test results
• Heavy Duty German Cutting Blades
• Available with Safety Latch Facility

GSM Balance:-

• Superior shock resistance & overload protection
• Software lock switch & integrated transportation lock
• Adjustable footrest with level indicator.

• Sample Area- 100 sq.cm
• Sample Diameter- 112.8 mm
• Handle material- Bakelite
• Movement of Handle- ¼ round to cut a sample

• Capacity : 200gm
• L.C. : 0.01gm
• * Other capacity 400gm, 600gm available on request
• * Models with higher accuracy also available
• Pan size : 120 mm
• Display : high contrast LCD display
• Power : AC adaptor (Included) or 4 AA battery (not included)
• Calibration : 200 gm brass weight (Included)
• Linearity : ± 0.01 g
• GSM least count : 1 GSM = (weight x 100)

Bursting Strength Tester - Digital Pneumatic cum Computerized is a consistent tool to indicate the Strength and performance of material like Rexene, leather, paper boards, paper, uneven boards and boxes, industrial fabric and solid fiber boards, filter cloth, plastic films, Foils, sheets, etc. PRESTO Bursting Strength Tester is manufactured under various Test Standards ASTM D 3786-01, ASTM D 3786 - 80A, ISO 1060 PART-1 1987.

Features

Specification:

The Presto leak detector machine is a high quality packaging seal integrity tester that adds quality control measures to your packaging applications. Regardless of contents, the vacuum seal integrity test will help ensure that your packaged product is sealed to your specifications. Benefits of will be realized by many industries from package manufacturers and converters to end user packagers in the packaging of: Coffee, foiled cups, gels, Pouches,grains, cereal, bakery, namkeen, chips, Confectionery, snacks, pasta, frozen foods, cheese, pet food and treats, Medical and pharmaceutical, and many more.

Features:

• Offers accurate and reliable results.
• Strictly complies with international quality standards.
• Provided by a calibration credential acceptable to NABL approved labs.
• Microprocessor-based for accuracy and repeatability
• Meets USP 28 Packaging Practice specification
• Automatic sample testing through easy vacuum mechanism
• Pressure, Inlet Vacuum Pressure setting, and Pre-set Timer function incorporated
• Changeable Timer Units in Hrs:min:sec
• Digital Pressure displays for easy pressure monitoring
• Stainless steel and powder coated body for corrosion resistant finish

Specifications:

• Vacuum adjustable up to – 900 mb (675 mm-Hg.)
• Box made of polished transparent PMMA (very rugged)
• Easy to use and safe
• 2 stage vacuum and holding time setting
• Accuracy: 0.5% of the measure
• Delivered with vacuum generator
• Customised Box with dimensions upon request

Presto Vacuum leak detection system is now available in Prima series. With HMI Touch Screen Display and fully automatic controls one can ensure accuracy with repeatability and take data acquisition for the various tests. It is capable of testing both Bottles/containers and other packages. The testing medium can be either air or water. It is the best instrument for accurate and quick testing of small to medium sized containers or packages.

Features:

• HMI based Touchscreen Model
• Microprocessor based controls for repeatability and accuracy
• Meets USP 28 packaging practice specification
• Air & Water both can be used as testing medium
• Automatic sample testing through easy vacuum mechanism
• Pass/ Fail criteria can be programmed.
• Changeable timer units in Hrs.: Min: Sec
• Inbuilt calibration facility
• Vacuum Pressure display incorporated in HMI for easy pressure monitoring
• Program profile for selecting test parameters and performing the test.
• East data management. User can create product identification, user name, vacuum hold time, set pressure, etc.
• Graph of Pressure vs. Time
• USB option available for storing test data and graph
• Print report with graph
• Data output in graphical and data record format.
• History data involves username, time, date, vacuum hold time, etc.

Specification:

• Vacuum adjustable up to – 900 mb (675 mm-Hg.)
• Box made of polished transparent PMMA (very rugged)
• Easy to use and safe
• Touch Screen display
• 2 stage vacuum and holding time setting
• Accuracy: 0.5% of the measure
• Delivered with vacuum generator
• Customised Box with dimensions upon request

• Microprocessor based display for accurate test results
• Display for compression strength of test specimen
• Separate fixtures for ring crush, edge crush and flat crush test.
• Highly accurate test results under compression force
• Strong gripping clamps.
• Bright LED display
• Inbuilt calibration facility
• Feather touch controls 

• Load Cell Capacity- 100 Kgf
• Display- LED (Digital)
• Accuracy- ±2% at full load (with master load)
• Least Count/Resolution- 0.01 Kgf
• Power- 220V, Single phase, 50 Hz
• Test Speed- 12.5± 2.5 mm/min

RCT/FCT/Edge Crush Tester is a consistent tool to measure the crush strength of cardboard boxes and packaging containers. PRESTO RCT/FCT/Edge Crush Tester is manufactured under Test Standard IS 7063.

Features:

• Microprocessor based display for accurate test results
• Display for compression strength of test specimen
• Separate fixtures for ring crush, edge crush and flat crush
• test.
• Highly accurate test results under compression force
• Strong gripping clamps.
• Bright LED display
• Inbuilt calibration facility
• Feather touch controls
• Graph test report is Force Vs Time
• 10 Sample test reports can be seen on one report
• Email facility of report
• Report Available in PDF format
• Pass/Fail Criteria can be programmed
• Easy Data Management. User can create product
• identification, test details etc.
• Inbuilt hardware/software CD

Specifications:

• Load Cell Capacity- 100 Kgf
• Display- LED (Digital), Graphical
• Accuracy- ± 2 % at full load (with master load)
• Least Count/Resolution- 0.01 Kgf
• Power- 220V, Single phase, 50 Hz
• Test Speed- 12.5 ± 2.5 mm/min

Digital GSM Balance instrument is a basic need for Quality Control, Dealers, Consumers and Developers & Manufacturers of paper, paper board, corrugated boxes, solid fiber board, and other materials.


Features:

• Display intensity.
• With memory.
• Compact wind shield with the scale.
• Precise and air free weighing due to Breeze shield.
• Complete supply with inspection & calibration certificate.
• Specially designed to determine the GSM of Paper & packaging.

Specification: 

• Mechanical and software protection to provide superior resistance from shock and overloading.
• Software locks to switch and integrated transportation lock.
• Capacity: 200 gm
• Sensitivity: 0.01 gm (10 mgm)
• Range: 200 GSM, 400 GSM & 600 GSM
• Endurance: proven durability
• Display: Digital(LED)

Box Compression Tester is a consistent tool to indicate the Compression strength of cardboard boxes so that it does not get deformed or crushed when stacked one above the other during storage or transit. PRESTO Box compression Tester is manufactured under various Test Standards ASTM D642, ASTM D4169, TAPPI T804, ISO 12048, and JIS Z0212.

Model Overview:-

• Microprocessor based display for accurate test results
• Highly accurate test results under uniform compression Force
• Strong base plate with rugged structure
• Bright LED display
• Feather touch controls
• Graph test report is Force Vs Time
• 10 Sample test reports can be seen on one report
• Email facility of report
• Report Available in PDF format
• Pass/Fail Criteria can be programmed
• Easy Data Management. User can create product identification,test details etc.
• Inbuilt hardware/software CD** Computer & Printer are not a part of the offer

Features:

• It comes with Dual System viz: 1) Digital Display ( Incase computer is not used/available )

                       2)Inbuilt hardware & software CD.

• The Graph Test Report is Force Vs Time .
• Report can be saved on desktop
• Data can be tabulated in Excel
• Report has description of Product name , Operator , Batch , Shape , Standard ,Date , Time & Remarks
• Pass/Fail criteria can be programmed
• Computer & Printer not a part of the offer
• Microprocessor based display for accurate test results
• Highly accurate test results under uniform compression Force
• Strong base plate with rugged structure
• Bright LED display
• Feather touch controls
• 10 Sample test reports can be seen on one report
• Email facility of report
• Report Available in PDF format
• Easy Data Management. The user can create product identification, test details, etc.

Specification:

• Display- • LED (Digital) • Graphical
• Accuracy- ± 2% full scale (with master load).
• Power- 220V, Single / Three phase, 50 Hz
• Test Speed- 12.5 ± 2.5 mm/min
• Communication Port- RS 232

• Microprocessor based PID controller
• HMI Based touchscreen Display
• Memory to hold up to 1 test reading
• Highly accurate test results under pneumatic pressure control.
• Strong heating jaws for performing tests
• No slippage in case specimen is tightened uniformly using clamping knobs without any loops.
• Speed Control through Variable Frequency Drive
• PID temperature controller

• Load Cell Capacity- 3 Kgf
• Display- TFT Touch Screen 4.3 Inch
• Accuracy- ± 1% at full scale (with master load)
• Least Count/Resolution- 3 gm
• Power- 220V, Single phase, 50 Hz
• Speed- Hot Tack:150mm/sec, Tension Test: 50 - 500mm/min
• Sealing Temperature- Ambient to 250ºC
• Dwell Heat Seal time- 0.1 – 999.9 Sec
• Dwell Hot Tack time- 0.1 – 999.9 sec
• Sealing Pressure- 2 – 7 Bar

• Microprocessor based display for accurate test results
• Highly accurate test results under pneumatic pressure control.
• Single Push button operation after setting PID temperature and time
• Strong heating jaws for performing tests
• No slippage in case specimen is placed uniformly without any loops.
• Bright LED display for temperature and timer
• PID temperature controller for highest level of controls and repeatability
• Digital Preset timer
• EN 31 hard and temper sealing jaw material
• Guide rod mechanism for efficient control of sealing
• Independent adjustment of temperature for upper & lower jaws

• Equipment Range- Ambient to 350ºC
• Sealing Temperature Working range- Ambient to 230ºC
• Accuracy- ± 1ºC
• Least Count/Resolution- 0.1ºC
• Power- 220V , Single phase, 50 Hz
• Sealing size- 150x 15 mm OR 300x 15 mm
• Temperature Controller- 4 digit PID
• Dwell Heat Seal time- 0.1 – 99.9 sec
• Timer- 4 Digit Digital
• Heat Sensor- Pt-100, Platinum Resistance Temperature Detector (RTD)
• Sealing Pressure- 2 - 6 Bar

• High-Quality rugged structure with corrosion resistant main body
• Falling pendulum type instrument
• Single-handed hassle-free operation
• Highly accurate test results under multiple pendulum weights
• Strong gripping fixture for holding test samples
• Pendulum release mechanism to cover various measuring range
• Inbuilt calibration weights

• Force for Pendulum- 1600, 3200 & 6400 gm force
• Constant Radius of Tear- 38 mm
• Unit Scale range- 0 -100%
• Slit Size- 20 mm
• Zero- Adjustable Zero Point
• Calibration Check weight At- 1600gf, at 3200gf, at 6400gf

• Display for Dynamic and Kinetic Friction - Force
• Highly accurate test results under sliding friction.
• Slider Block for performing tests – Sample to Sample, glass or metal
• No slippage in case specimen is tightened uniformly using fly screws without any loops.
• Bright LED display
• Feather touch controls
• Compressive force clamp with hardened thread screw operated

• Load Cell Capacity- 3 Kgf
• Display- LED (Digital)
• Accuracy- ±2% at full load (with master load)
• Least Count/Resolution- 3 gm
• Power- 220V, Single phase, 50 Hz
• Speed- 150 ±30 mm/min
• Motor- 15 kg/cm2 torque, 60rpm

A coefficient of Friction Tester – Digital Cum Computerised is a consistent tool to indicate the starting and sliding friction of plastic films and sheets when sliding over itself or other substance at specified test condition. PRESTO Coefficient of Friction Tester is manufactured under various Test Standards ASTM D 202, ASTM D 4918, ASTM D 1894, ISO 8295, and TAPPI T 815.

Features:

• Microprocessor based display for accurate test results
• Display for Dynamic and Kinetic Friction
• Highly accurate test results under sliding friction - force.
• Slider Block for performing tests – Sample to Sample, glass or metal
• No slippage in case specimen is tightened uniformly using without any loops.
• Compressive force clamp with spring operated
• Feather touch controls
• Easy Data Management. The user can create product identification, test details etc.
• Graph test report is Force Vs Time.
• 10 Sample test reports can be seen on one report
• Email facility of report
• Data can be tabulated in excel format
• Pass/Fail Criteria can be programmed
• Inbuilt hardware/software CD

Specification:

• Load Cell Capacity- 3 Kgf
• Display- • LED (Digital)             • Graphical
• Accuracy- ±2% at full load (with master load)
• Least Count/Resolution- 3 gm
• Power- 220V, Single phase, 50 Hz
• Speed- 150 ±30 mm/min
• Motor- 15 kg/cm² torque, 60rpm
• Communication Port- RS 232

• High-Quality rugged structure with corrosion resistant main body
• Microprocessor based display for accurate test results
• Display for impact/absorbed energy and angle of the test specimen
• Single-handed hassle-free operation
• Highly accurate test results under impact forces
• Strong gripping fixtures for holding test samples.
• Oscillatory Pendulum release mechanism
• Bright LED display
• Puncture Headcollar with soft adjustment to puncture the head base
• Inbuilt calibration facility
• Feather touch controls

• Energy Range of Weights 6, 12, 24 Jule per meter
• Accuracy ± 2% within full range
• Release angle of Pendulum 90º
• Display LED (Digital) 7 segment
• Power 220V, 50Hz, Single Phase